recovery or salvage. Items not coded are expendable.
ized for the number of equipments supported.
Recoverability codes are:
Subsequent appearances of the same item will have the
letters "REF" in the allowance columns.
Items
Code
Explanation
authorized for use as required but not for initial stockage
are identified with an asterisk in the allowance column.
R
Repair parts and assemblies which are
(2) The
quantitative
allowances
for
economically repairable at DSU and GSU
organizational level of maintenance represents one initial
activities and normally are furnished by a
prescribed load for a 15-day period for the number of
supply on an exchange basis.
equipments supported.
Units and organizations
S
Repair parts and assemblies which are
authorized additional prescribed loads will multiply the
economically repairable at DSU and GSU
number of prescribed loads authorized by the quantity of
activities and normally are furnished by supply
repair parts reflected in the density column applicable to
on an exchange basis. However, when these
the number of items supported to obtain the total quantity
items are determined to be uneconomically
of repair parts authorized.
repairable by a GSU, they will be evacuated to
(3) Organizational units providing maintenance
a depot for evaluation and analysis before final
for more than l00of these equipments shall determine
disposition.
the total quantity of parts required by converting the
T
High dollar value recoverable repair parts which
equipment quantity to a decimal factor by placing a
are subject to special handling and are issued
decimal point before the next to last digit of the number
on an exchange basis. Such repair parts
to indicate hundredths, and multiplying the decimal factor
normally are repaired or overhauled at depot
by the parts quantity authorized in the 51-100
maintenance activities.
equipments is 40; for 150 equipments multiply 40 by 1.50
U
Repair parts specifically selected for salvage by
or 60 parts required.
reclamation units because of precious metal
(4) Subsequent changes to allowances will be
content, critical materials, high dollar value
limited as follows: No change in the range of items is
reusable casings or castings.
authorized. If additional items are considered necessary,
b. Federal Stock Number, Column 2. This column
recommendation should be forwarded to Commanding
Officer, Edgewood Arsenal, ATTN: SMUEATSE-TPL,
indicates the Federal stock number assigned to the item
Edgewood Arsenal, Md. 21010 for exception or revision
and will be used for requisitioning purposes.
c. Description, Column 3. This column indicates
to the allowance list. Revisions to the range of items
authorized will be made by Edgewood Arsenal based
the Federal item name and any additional description of
upon engineering experience, demand data, or TAERS
the item required. A part number or other reference
information.
number is followed by the applicable five-digit Federal
supply code for manufacturers in parentheses. Repair
g.G Illustration, Column 7. The illustrations in this
parts quantities included in the kits, sets,
and
manual are identical to those published in the -35P. The
assemblies are shown in front of the repair part name.
-35P illustrations are given for a better understanding of
d. Unit of Measure (U/M), Column 4. A two
the parts relationship; however, only those parts
character alphabetic abbreviation indicating the amount
assigned a maintenance code "O" are listed in the
or quantity of the item upon which the allowances are
tabular portion. Only these parts are authorized for
based, e.g., ft, ea, pr, etc.
requisitioning from this manual. This column is divided
e. Quantity Incorporated in Unit, Column 5. This
as follows:
column indicates the quantity of the item used in the
(1) Figure number, column 7a. Indicates the
functional group. A "V" appearing in this column in lieu
figure number of the illustration In which the item is
of a quantity indicates that a definite quantity cannot be
shown.
indicated (e.g., shims, spacers, etc).
(2) Item number, column 7b. Indicates
f. 15-Day Organizational Maintenance Allowance,
Column 3 of Section II and Column 6 of Section III and
IV.
(1) The allowance columns are divided into four
subcolumns. Indicated in each subcolumn opposite the
first appearance of each item is the total quantity of items
author-
3
